Welcome to SPCA’s documentation!¶
SPCA is an open-source, modular, and automated pipeline for Spitzer Phase Curve Analyses.
To install SPCA, run the following in a terminal:
git clone https://github.com/lisadang27/SPCA.git cd SPCA pip install . # IF you want to install george to run GP analyses, also then run pip install .[GP]
Please note however that SPCA is in a state of alpha testing and is still under development. Frequent changes are expected over the upcoming few months as we finalize some aspects like PSF fitting with aperture photometry or nearby companion removal using PSF subtraction.
As of version 0.3, we have made some important changes. These include:
- Added the ability to perform full-frame photometry
- Added the ability to fit unbinned photometry
- Added the ability to decorrelate using PSF-fitted centroids using the “_PSFX” mode suffix
- Added sigma-clipping along full time axis (not just within data cube). This comes at the cost of needing to load all frames into RAM at the same time which can be quite RAM intensive for some phase curves. Will consider allowing user to switch to using dask in the future to reduce RAM cost when performing photometry at the cost of slower run speeds.
- Changed BLISS knot density selection algorithm to be more like POET’s algorithm
- Added a progress bar for when running photometry
- No updates on emcee freezing, but it now rarely ever occurs for me (Taylor). Perhaps the better initialization routine is helping here.
As of version 0.2, we have made some important changes and some bug fixes. These include:
- Renamed decorrelation and fitting file to Decorrelation (.py and .ipynb)
- Full integration of PLD and PLDAper models
- Reduced the amount of static code that the user sees and placed this in separate files instead.
- Changed how photometry is saved. This will not be noticeable unless you want to use PLDAper models which cannot be run with the old photometry.
- Also changed the units in which the photometry is saved so that it is easy to compute the photon noise limit - a calculation that was previously done incorrectly.
- The emcee fitting routine sometimes freezing still seems to be an issue as of v0.2. This seems to be caused by the combination of a large dataset and either a large model or a poorly initialized model. Previous attempts at forcing a timeout have failed without directly editing emcee or multiprocessing code. If this occurs to you and you need to analyze your data soon, I’d recommend removing the few lines that use multiprocessing - contact us if you have a hard time doing this. We are looking into different samplers (such as PyMC3) to resolve this issue.
- Follow the installation instructions at the top of this page to ensure you have all of the necessary dependencies.
- To use SPCA, you must first download your Spitzer data from the Spitzer Heritage Archive: https://sha.ipac.caltech.edu/applications/Spitzer/SHA/. Place the downloaded zip files in a directory with the same name as the planet (exluding spaces).
Most of the following commands have an .ipynb ending and .py ending option available, where the .py version is optimized for analyzing many data sets and the .ipynb file is optimized for viewing the analysis of a single data set. Each file has a portion at the top where you can set parameters which will determine the techniques.
- Next, use the Make_Directory_Structure file to extract the data and setup the required directories.
- Then use the Everything_Photometry file to perform a suite of different photometries on your data. The code will automatically select the best aperture photometry method which gives the lowest scatter after smoothing the raw flux by a boxcar filter of a width provided by the user.
- Then use the QuickLook file to ensure that you have looked at the raw data (to ensure it looks reasonable) and to determine whether you want to remove the first AOR (in case it is a short AOR to be discarded). By looking at the raw data, you can gain some insight into how successful different decorrelation models might be.
- Then decorrelate the data using the Decorrelation file. Most parameters here are explained with a nearby comment. One key parameter though is the “mode” which sets the decorrelation method used. Modes that contain “Poly#” use a 2-dimentionsal polynomial of order #, modes that contain “BLISS” use BiLinearly-Interpolated Subpixel Sensitivity mapping, modes that contain “GP” use a Gaussian Process using x and y centroid positions as covariates, and modes that contain “PLD#_$x$” use Pixel Level Decorrelation of order # (1 or 2) and use a pixel stamp size of $ by $ (3x3 or 5x5). PLD performed using aperture photometry (the recommended PLD technique) can be accessed using “PLDAper#_$x$”. Each mode is then followed by an underscore and either “v1” or “v2” indicating the use of either a 1st or 2nd order sinusoidal model for the phase variations. If “PSFX” is present in the mode string for non-PLD models, the data are decorrelated using the PSF-fitted centroids rather than the flux-weighted mean centroids. If “ellipse” is present in the mode string, phase variations due to the elliptical shape of the planet are modelled. Any other text can be added to the mode keyword for your own convenience (e.g. “Poly2_v1_run2” or “PLDAper2_5x5_v1_testingFit”).
- Finally, some tables containing a selection of the fitted parameters from each model run can be made using the MakeTables file. These tables will also highlight the best decorrelation method for each analysis, determined using delta-BIC (selecting your model is actually quite a challenging and complicated step, and user discretion is absolutely recommended).
- SPCA package
- SPCA.Decorrelation_helper module
- SPCA.Photometry_Aperture module
- SPCA.Photometry_Common module
- SPCA.Photometry_Companion module
- SPCA.Photometry_PLD module
- SPCA.Photometry_PSF module
- SPCA.astro_models module
- SPCA.bliss module
- SPCA.detec_models module
- SPCA.frameDiagnosticsBackend module
- SPCA.freeze module
- SPCA.helpers module
- SPCA.make_plots module
- SPCA.make_plots_custom module
- SPCA.photometryBackend module
- Module contents
Lisa Dang contributed the initial code and idea for SPCA, and wrote much of the photometry and fitting routines, as well as the polynomial and PLD decorrelation methods.
Both authors worked extensively to debug the code and simplify the user experience.
Taylor James Bell further generalized and streamlined SPCA, allowing it to be run quickly and easily for any given planet with minimal effort. Taylor also contributed most of the documentation, and the GP decorrelation method.
We thank Joel Schwartz for his aid in writing out BLISS decorrelation method. We also thank Dylan Keating for alpha testing SPCA. We thank Antoine Darveau-Bernier for writing code to parse through the Exoplanet Archive data and select the best constrained value for each parameter in the database (code can be found here).
License & Attribution¶
Copyright © 2018-2020 Lisa Dang & Taylor James Bell.
SPCA is free software made available under the GPL3 License. For details see the LICENSE.